The Basics of Plumbing Knowledge for Bathtub Installation
The Basics of Plumbing Knowledge for Bathtub Installation
Blog Article
Just how do you actually feel in regards to How to Install a Bathtub?
Installing a bath tub isn't specifically rocket science, but it does require strong plumbing, carpentry, and in some cases, tiling abilities. Replacing an old tub with a new one is also a moderately challenging task. If the old tub is easily available, the task can move immediately; if you need to open a wall surface to remove the old tub and position the brand-new bath tub, the job is a lot harder. In either case, the task is within a house handyman's abilities, although you will need an assistant to leave the old tub as well as set in the new one. Ensure you have actually qualified yourself for the work as well as fit trying it. Rather than hiring a professional to take over a halfway-completed project, it is far better to take into consideration utilizing one prior to you start. Possibilities are you might require a professional plumber to make tube connections.
This article will certainly help you set up a brand-new bathtub in your bathroom if you have actually already acquired a brand-new bathtub and don't require to alter the setup of your previous water supply pipelines.
Your devices and material list need to consist of the following:
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installation, after that the first thing you need to do is detach the water supply. After doing so, activate the faucets to drain pipes any type of water continuing to be in the system. The process of getting rid of the existing faucets can be quite bothersome because of the limited accessibility that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a cloth prepared for the staying water that will certainly originate from the pipelines. Once the supply pipes have actually been removed, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary faucets from turning throughout this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing substance.
Prior to proceeding to fit the new taps, contrast the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the new taps to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly require a plastic port to avoid damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end offers a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will require decreasing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making sure that the washing machines remain in location between the tap and the sink. Secure the tap in position with the maker provided backnut. Once the faucet is securely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal tap ports. The former kind should be attached to the faucet ends initially, tightening up just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Making use of both wood boards under its feet, place the tub in the called for position. The wooden boards are practical in equally spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 little points.
The following objective is to guarantee that the tub is leveled all round. This can be achieved by checking the spirit level and readjusting the feet on the bath tub till the spirit level reads degree.
To set up taps, fit the bottom of the furthest flexible tap connector to the suitable supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Activate the water as well as examine all joints and brand-new pipework for leakages and tighten them if required. Load the bathtub as well as also examine the overflow outlet and the regular outlet for leakages.
Lastly, take care of the bathroom paneling as described in the maker's user's manual. Tiling and also securing around the tub needs to wait till the bathtub has been made use of a minimum of once as this will settle it right into its last position.
Getting ready for the Setup
Firstly, the sustaining frame supplied with the bathroom should be fitted (if called for) according to the maker's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is necessary to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the faucets device to stop strain on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to currently prepare to be suited its last placement.
Tiling Around the Bath tub
In the area where the bathroom fulfills the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to crack an inflexible seal, causing the water to pass through the wall surface in between the bathroom and also the tiling, causing complications with dampness as well as possible leakages to the ceiling below.
You can select from a range of coloured sealants to assimilate your fixtures and also installations. They are offered in tubes and cartridges, and can sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched newspaper or soft rope. Bear in mind to constantly fill the bathtub with water prior to securing, to enable the movement experienced when the tub is in usage. The sealant can break relatively early if you do not consider this activity prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly readily available on the market. It is a good idea to fit the floor tiles making use of water-resistant or water resistant glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I stumbled upon that piece on How to Install a Bathtub Yourself when browsing the web. If you liked our blog entry plz be sure to pass it around. Bless you for your time. Please check our website back soon.
Tailored emergency solutions; call now. Report this page